Welcome to the world of Saab ! Register

Search:

Type: Posts; User: lookforjoe

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    65
    Views
    45,196

    Got the car running with the 514 ECU, with a chip...

    Got the car running with the 514 ECU, with a chip flashed with the Volvo 554 bin, and the 005 MAF. Added a 12v feed to pin 4, and removed the grounds used by Volvo for pins 14 & 19 at the ECU. Now I...
  2. Replies
    65
    Views
    45,196

    Found the problem, after looking at Volvo LH2.2...

    Found the problem, after looking at Volvo LH2.2 (plastic case MAF), LH II wiring (metal case MAF) and Porsche 928 LH2.2 schematics. Couldn't find a frikkin Saab Wiring Diagram anywhere.

    Volvo...
  3. Replies
    65
    Views
    45,196

    Fixed the current supply issue. Problem I have...

    Fixed the current supply issue.

    Problem I have with the Saab 514 ECU is that it is supplying over 9v at the idle offset line, and is holding the filament in burn off mode. I've tried two different...
  4. Replies
    65
    Views
    45,196

    The one niggling problem I have had since adding...

    The one niggling problem I have had since adding the EZK ignition back in October, was a idle surge when warm. If I stepped on the brake, put it in reverse, turned on the lights, etc., it would cause...
  5. Replies
    65
    Views
    45,196

    I don't know - significantly more than stock. I...

    I don't know - significantly more than stock. I will be taking it to the dyno once I have the idle/surge issue resolved. :)
  6. Replies
    65
    Views
    45,196

    Don't know what year precisely. I'm assuming...

    Don't know what year precisely. I'm assuming 86-87 as it matches the Volvo setup of the same time frame.

    The wiring is the same, I have switched between the two. Only difference I can see is Volvo...
  7. Replies
    65
    Views
    45,196

    OK - so I've tried a used and a rebuilt 005 MAF,...

    OK - so I've tried a used and a rebuilt 005 MAF, and I cannot get the engine to run using the 514 ECU (with the MAF plugged in). I get a steady 8-9v output on the idle offset (CO adjust) terminal at...
  8. Replies
    65
    Views
    45,196

    Going to pick up another 005 MAF, so I can try...

    Going to pick up another 005 MAF, so I can try again to modify the fueling map & rpm limit.

    About 1000 miles on the motor since the rebuild and the addition of LH2.2
  9. Replies
    65
    Views
    45,196

    Added larger Volvo throttle body ...

    Added larger Volvo throttle body

    http://saabworld.net/images/imported/2014/10/6.jpg

    http://saabworld.net/images/imported/2014/10/7.jpg
  10. Replies
    65
    Views
    45,196

    Turns out the Saab MAF I bought had a broken...

    Turns out the Saab MAF I bought had a broken hotwire. I bought it so long ago I can't get a replacement via the eBay seller, even though I did alert him at the time of purchase that there was a crack...
  11. Replies
    65
    Views
    45,196

    Can't run the 514 ECU & 005 MAF; no matter which...

    Can't run the 514 ECU & 005 MAF; no matter which map I use, it doesn't run right.

    I switched to a Volvo 554 (Volvo update for 511/544 ECUs with cold start/warmup issues) ECU & 007 MAF. With...
  12. Replies
    65
    Views
    45,196

    Engine fired right up, but ran very rich, with...

    Engine fired right up, but ran very rich, with the AFR's dropping into the 10's very shortly after starting(!) Hoping I didn't wash the bores of my brand new engine & cause premature wear...

    I...
  13. Replies
    65
    Views
    45,196

    Regarding Map adjustments, I re-read the thread ...

    Regarding Map adjustments, I re-read the thread on ECUProject - lowering the table values increases fuel. So, I will increase the values 16%, and burn a chip. See how that goes. Getting closer to...
  14. Replies
    65
    Views
    45,196

    I don't know Raul, perhaps another does. I...

    I don't know Raul, perhaps another does.

    I found this pic, which helps with the chip orientation :)

    http://saabworld.net/images/imported/2014/07/7.jpg

    Finally have a partial driveway to work...
  15. Replies
    65
    Views
    45,196

    I'm hoping someone on here has a 514 ECU - or pic...

    I'm hoping someone on here has a 514 ECU - or pic of the correct chip orientation relative to the socket - I realized I never took a pic before I removed the chip, and it's now been long enough that...
  16. Replies
    65
    Views
    45,196

    Harness finished & checked on motor ...

    Harness finished & checked on motor

    http://saabworld.net/images/imported/2014/05/1.jpg

    http://saabworld.net/images/imported/2014/05/2.jpg

    finally had good enough weather to get out & work in...
  17. Replies
    65
    Views
    45,196

    Modified the stock runners instead - the custom...

    Modified the stock runners instead - the custom required too many angle alignments at the same time to fit - I found that the runner / plenum flanges are also offset in two planes.
    ...
  18. Replies
    65
    Views
    45,196

    Wiring harness mostly complete - have to add the...

    Wiring harness mostly complete - have to add the injector feeds

    http://saabworld.net/images/imported/2014/01/18.jpg
  19. Replies
    65
    Views
    45,196

    Looking at the wiring I found for the Saab... ...

    Looking at the wiring I found for the Saab...

    http://saabworld.net/images/imported/2014/01/15.jpg

    Compared to the Volvo version..

    http://saabworld.net/images/imported/2014/01/16.jpg
    ...
  20. Replies
    65
    Views
    45,196

    Thanks, Sam. I'm basing the map settings on...

    Thanks, Sam.

    I'm basing the map settings on the (in bold) statement on Eddy's post:



    Looking at the two maps he posted, the larger injector map has lower values. What I don't understand is...
  21. Replies
    65
    Views
    45,196

    I can't find the specification on the stock FPR...

    I can't find the specification on the stock FPR for the 86-88 900 that uses the 514 ECU and 005 MAF.

    I need to determine the % difference in flow from Saab stock (19lb @ 2.5 or 3 bar?) - the...
  22. Replies
    65
    Views
    45,196

    Got my USB programmer & software that runs in...

    Got my USB programmer & software that runs in Win7

    http://saabworld.net/images/imported/2014/01/3.jpg

    Read the BIN from my 514 chip to test it
    ...
  23. Replies
    65
    Views
    45,196

    More issues. Willem Programmer software doesn't...

    More issues. Willem Programmer software doesn't like Win7 either. Contacted the vendor, and he said that you probably can't burn chips from a laptop, even if you get the software loaded. This is...
  24. Replies
    65
    Views
    45,196

    Hmm... LH22Editor won't install in Windows 7...

    Hmm... LH22Editor won't install in Windows 7 :cry:

    I think my much older Toshiba has XP, I'll have to try that. Not a PC person, so I have no clue what's up - error messages when trying to write...
  25. Replies
    65
    Views
    45,196

    Thanks for the reply - since I'm planning on...

    Thanks for the reply - since I'm planning on using the 514 ECU & BIN as my starting point, I went ahead & got a 005 MAF off eBay. I don't know if flashing with the Volvo BIN would make any...
Results 1 to 25 of 31
Page 1 of 2 1 2
All times are GMT. The time now is 04:45.
Powered by vBulletin® Version 4.2.5
Copyright © 2024 vBulletin Solutions Inc. All rights reserved.