Welcome to the world of Saab ! Register

Search:

Type: Posts; User: GeoffR

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    270

    There was most certainly an Aero in 2006 but...

    There was most certainly an Aero in 2006 but possibly not in your market.
    From experience the rotors last through two sets of pads. Depending on whether you drive a manual or auto and your driving...
  2. Replies
    6
    Views
    270

    The key to getting the correct parts is to use...

    The key to getting the correct parts is to use the VIN which can be found on the panel visible through the bottom of the windscreen (windshield to you) just in front of the driver (visible from...
  3. Replies
    3
    Views
    450

    How much do you pay for a litre of fuel in Canada...

    How much do you pay for a litre of fuel in Canada at the moment?

    Sorry but I have never seen the attraction of Diesel engines, possibly because the smell used to make me sick (physically). Looks...
  4. Replies
    4
    Views
    476

    Seems GM don't recognise the p/n You could try...

    Seems GM don't recognise the p/n
    You could try here though https://www.saabits.com/index.php?main_page=products_all&disp_order=5&page=10
  5. Replies
    4
    Views
    476

    If you have EPC, you can find a download link...

    If you have EPC, you can find a download link elsewhere on this site, you can find the part number, it is probably generic GM so a Holden dealer might be a good start.
  6. Thread: Engine issues

    by GeoffR
    Replies
    3
    Views
    374

    OK, I don't remember the ignition circuit but you...

    OK, I don't remember the ignition circuit but you need to start at the beginning by checking that each position of the ignition switch powers the expected circuits. I am sorry but without the wiring...
  7. Thread: Engine issues

    by GeoffR
    Replies
    3
    Views
    374

    If wiring the coil directly gets the engine to...

    If wiring the coil directly gets the engine to start but it stops again after a period I would try replacing the coil.
    you really aren't going to get to the bottom of the problem without wiring...
  8. Thread: PCV valve check

    by GeoffR
    Replies
    8
    Views
    614

    OK the valve works. Unfortunately I am not...

    OK the valve works. Unfortunately I am not familiar with the 3.0 V6 engine so I would advise downloading WIS and using that to guide your troubleshooting..
  9. Thread: PCV valve check

    by GeoffR
    Replies
    8
    Views
    614

    That would seem reasonable, did you try blowing...

    That would seem reasonable, did you try blowing through it both ways? It wouldn't be unknown for it to be assembled incorrectly of simply not working.
  10. Thread: PCV valve check

    by GeoffR
    Replies
    8
    Views
    614

    Turn it the other was around.

    Turn it the other was around.
  11. Replies
    1
    Views
    1,512

    Better late than never part 2 Soldered...

    Better late than never part 2
    Soldered connections.
    Many people have the mistaken idea that a soldered connection is the best possible electrical connection. This is unfortunately only true if the...
  12. Replies
    5
    Views
    784

    I would still recommend replacing both.

    I would still recommend replacing both.
  13. Replies
    10
    Views
    1,222

    Many of the plastics used on the 9000 and 9-5...

    Many of the plastics used on the 9000 and 9-5 have proved, over an extended period, to be unsuitable for use in the high temperature environment of the engine bay. In the majority of cases the...
  14. Replies
    10
    Views
    1,222

    If you remove the pipe between the air mass meter...

    If you remove the pipe between the air mass meter and the elbow (the black pipe at the bottom middle) you can get inside and push upwards or at least prevent debris falling in.
  15. If it is the crankshaft oil seal it is...

    If it is the crankshaft oil seal it is comprehensively blown. I was actually thinking that was what it was from the photographs.
  16. The oil pressure switch is on the back of the...

    The oil pressure switch is on the back of the engine above the exhaust, nowhere near the polyvee belt. The timing cover is a distinct possibility.
  17. I don't like to say this but I think you are...

    I don't like to say this but I think you are going to need a local expert, it is really nearly impossible to do a diagnosis at a distance.
  18. Replies
    5
    Views
    784

    If you can get a bulb that works, replace both of...

    If you can get a bulb that works, replace both of them, with luck that will prevent the warning. The 1077 seems to be available from at least one eBay seller in your Southern neighbour. I also found...
  19. You mean Right hand, Wagon or saloon (sedan)?

    You mean Right hand, Wagon or saloon (sedan)?
  20. Replies
    3
    Views
    1,350

    I am sorry nobody replied to your original post...

    I am sorry nobody replied to your original post but then Classic 900s are not terribly common any more. It is over 30 years since I last owned one and it was far too young to have suffered any of the...
  21. Replies
    25
    Views
    44,109

    This is the circuit diagram for a 2007 9-5 with...

    This is the circuit diagram for a 2007 9-5 with Xenons. It came from WIS where the other diagrams can also be found,
    17415
  22. Yes there should be a drain on each side, the...

    Yes there should be a drain on each side, the driver's side on your car would be the passenger side on a RHD model so have a look at a UK forum for how to clear it.
  23. Replies
    2
    Views
    722

    Do you have comfort opening, hold the unlock...

    Do you have comfort opening, hold the unlock button to the key fob for four seconds and all four windows open? If that works it may be just the switch as it clearly works when you hold the switch to...
  24. Replies
    4
    Views
    891

    Frank, that thread refers to the original 9-5 but...

    Frank, that thread refers to the original 9-5 but this thread refers to the NG 9-5 and things are slightly different. Also, dgreaves is in the UK with a different range of suppliers.
  25. Replies
    4
    Views
    891

    SaaBits should be able to source the correct...

    SaaBits should be able to source the correct parts at a good price.
Results 1 to 25 of 493
Page 1 of 20 1 2 3 4
All times are GMT. The time now is 17:49.
Powered by vBulletin® Version 4.2.5
Copyright © 2021 vBulletin Solutions Inc. All rights reserved.