Results 11 to 20 of 25
-
20 August 2012 #11
- Join Date
- 13 Aug 2012
- Location
- Toronto
- Posts
- 3
- Saab(s)
- 2004 9-5 Arc wagon
-
20 May 2013 #12
- Join Date
- 20 May 2013
- Location
- Michigan
- Posts
- 1
- Saab(s)
- 2003 9-5 Linear
I cant get the second click! Using large channel-locks. I dont want to damage window or roller rails. Anyone come up with a diffent method to squeeze thru second click? thanks
-
20 May 2013 #13
Frank Administrator
- Join Date
- 30 Jul 2010
- Location
- USA - Netherlands
- Posts
- 7,901
- Saab(s)
- previous: 2006 9-3, 2001-06 9-5, 2011 9-4X
I think mine only had a single click as well. I didn't want to force it and the window worked fine.
-
21 May 2013 #14
My new window roller arrived today. Time to start tearing up teh door. By the looks of things, this is no isolated fault on Saabs...
-
26 July 2013 #15
Renato Piereck Spreading the Saab virus
- Join Date
- 24 Jul 2011
- Location
- Ansbach, Germany
- Posts
- 1,520
- Saab(s)
- '00 9-5 Aero SC, 87 900i 8v
Well, I had my driver's side window do the shark fin tilt last month. It was a day before I had an appointment at the Saab dealer to replace a wheel bearing and they did the regulator replacement too.
Well, today it's flipping hot here, and lo and behold, the same window again did the shark fin into the door, so apparently the regulators broke again. I'll be going by the dealer tomorrow and buying a pair of regulators and doing the job myself, so I was happy to find a tutorial here at SW. I'll also be ordering some regulators from the US (cheaper) in the event they fail a third time! Since the parts are cheap might as well have them handy.Now: '00 Saab 9-5 Aero Combi - '89 Peugeot 205 CTI - '91 Peugeot 309 GTI
Gone: '87 Saab 900i - '95 Saab 900 SE Turbo
-
26 July 2013 #16
Frank Administrator
- Join Date
- 30 Jul 2010
- Location
- USA - Netherlands
- Posts
- 7,901
- Saab(s)
- previous: 2006 9-3, 2001-06 9-5, 2011 9-4X
I have 2 spare rollers in my tool bag in the car. With my luck, one will break while I am on a road trip on a Saturday night at 7:00pm, far away from any place that may sell these. I think I can replace one in about 30 minutes anywhere. Now that I have them on hand, they will probably never break again though..
-
28 August 2013 #17
Sarah Saab Fan
- Join Date
- 28 Aug 2013
- Location
- Bedford, N. S. Canada
- Posts
- 18
- Saab(s)
- 2002 9-5 2.3t wagon, 2004 9-5 Sedan
HI all...we just did this in May when I had just moved. Thank goodness we have a garage. I got mine from the local dealer that sells Saab parts for $7.00 each. And I thought Canada was expensive. I guess not.
-
28 December 2013 #18
- Join Date
- 28 Dec 2013
- Location
- Cirencester England
- Posts
- 6
- Saab(s)
- 9-5 2.3t Estate 2006; 9-3 SE 2001
Have just completed this job on my 9-5 after consulting this site - the pics were extremely helpful, thanks. I followed the same procedure up to the point where you say "do not remove the securing pin from the roller" - in fact, I DID remove the pin, slid the roller into the guide, pushed the regulator into the roller and then re-attached the pin to the roller. It`s a bit fiddly this way, and be prepared to lose the pin inside the door a couple of times ( I used a telescopic rod with a magnet on the end to retrieve it), but it saves having to force the regulator "pin" throught the roller which is equally tricky in my opinion.
-
21 September 2016 #19
Frank Administrator
- Join Date
- 30 Jul 2010
- Location
- USA - Netherlands
- Posts
- 7,901
- Saab(s)
- previous: 2006 9-3, 2001-06 9-5, 2011 9-4X
The window rollers broke on my 2005 9-5 last weekend. I don't think there was any worse location this could happen... I drove into a car wash, opened the window to pay and was ready to roll through the car wash. And yes.. I wanted to roll up my window and it just fell back in the door.
They were able to let me back out and fortunately there was only one other car behind me. And it could have been worse as this car wash is usually busy on Saturdays.
Ah well, hopefully these new rollers will last another 10 years.
-
01 November 2017 #20
- Join Date
- 08 Jul 2011
- Location
- Henderson, NV ( Las Vegas )
- Posts
- 50
- Saab(s)
- 2003 Burgandy Areo 9-5
Green Window Roller Replacement - Saab 9-5
I read all these replies, great replies. Someone mentioned setting the window stops. I had no idea there was a stop setting, I do agree that there is a coralation between the stops and the green roller breaking. So, how does one find and set these stops?
Also after replacing the green rollers on the passenger side front window the window raises to the close position, but on the way up it tends to have a gap to the rear of the window. It can be pushed by hand to the rear and then it will close. I know you guys have the answers and thanks up front.
Similar Threads
-
Is this gap in the window trim normal?
By Dave T in forum Saab 9-3 (2003-2014)Replies: 8Last Post: 17 August 2011, 08:45 -
How to tell if a roller or ball bearing is bad
By euromobile900 in forum Tech TalkReplies: 6Last Post: 23 December 2010, 22:18 -
Car window cleaning tips?
By Dave T in forum Tech TalkReplies: 3Last Post: 19 August 2010, 13:13