Welcome to the world of Saab ! Register
Results 1 to 2 of 2
  1. #1
    Saab Enthusiast raquettelaker2's Avatar
    Join Date
    05 Aug 2010
    Location
    Connecticut
    Posts
    53
    Saab(s)
    2008 9-3 Turbo-X, 1994 900 CommEd
    Thumbs Up:   6

    Sedan Boot/Trunk Lid Wire Harness Repair - Saab 9-5

    One of the Saab 9-5 sedan's few design-flaws is that the wire bundle that runs from the car body to the trunk lid makes a 180 degree turn around the sharp edge of the plastic elbow in the lid. This eventually leads to broken wires and some fun electrical situations. These wires power the reverse lights, fog lights, latch actuator, anti-theft micro-switch, and license plate lights. You might notice for example if the micro-switch wire breaks the trunk can be wide open and the dash won't tell you, or you can open the trunk without the alarm going off, and the light in the trunk won't illuminate. My actuator wire broke so I had to crawl in through the back seat to pull the emergency release cord.

    Name:  harness 1.jpg
Views: 9839
Size:  21.8 KB

    First off, you need to remove the lining on the trunk lid. There are a bunch of those push-pin fasteners along the edges, and you need to unscrew the torx screws that hold the grab-handle in place. If you have an earlier 9-5 with the warning triangle mounted in the lid, I couldn't figure out how to remove the brackets without breaking them when I did this repair in my 2001. In my newer car, a 2004, the triangle was deleted, but I still had to destroy the two black fasteners to get them out. If anyone knows secret I don't I'd love to hear it! If your 9-5 has the emergency pull release, the cable slips out of the clip so you can pull the handle off.

    Circled below in red are all the harness connectors. From left: reverse/fog housing, micro-switch to tell anti-theft the trunk is open (top), license plate lights (bottom), trunk actuator, and the other reverse/fog light housing. Circled in green is one of the white clips that hold the wires against the lid. Bend them to one side and wiggle a little and they come out pretty easily. I labeled all the connectors before unplugging them but probably could have managed without that step.

    Name:  harness 2.jpg
Views: 9841
Size:  40.5 KB

    In the trunk now, open the door to access the brake lights on the driver side. The green bundle of wire in electrical tape going to that white connector is the trunk lid harness. Release the tab on the connector and unplug it.

    Name:  harness 3.jpg
Views: 9587
Size:  22.5 KB

    If you stand to the side of the car and twist the plastic elbow that runs into the trunk lid clockwise and HARD, the right-side clip will release (sounds like it's breaking, but it shouldn't) and the left side then slides out. Where the harness runs into the body of the car is just a rubber hose and it pulls right out. The hard plastic tube clipped onto the hinge assembly next to the gas lift un-clips from the hinge.

    Name:  harness 4.jpg
Views: 9470
Size:  42.1 KB

    Here's what it looks like out of the car:

    Name:  harness 5.jpg
Views: 9420
Size:  32.9 KB

    I bought some 18 gauge automotive wire from Walmart and shrink tubing from Radio Shack. I spliced in about 12" of wire, but you might even want to do more so that your splice connections on either side can be in the car and in the lid and not running between. I crammed all mine into the hard plastic tube attached to the hinge so they wouldn't bend. For the splices I cut 1/2" of insulation off the ends, twisted the wires together, soldered them, and used a heat-gun (HOT - BE CAREFUL!) to shrink the shrink tube.

    Name:  harness 6.jpg
Views: 9363
Size:  40.6 KB

    Name:  harness 7.jpg
Views: 9335
Size:  44.0 KB

    Name:  harness 8.jpg
Views: 9346
Size:  45.6 KB

    Now you just feed the harness back into place. I wrapped the section of wire that bends tightly in a couple layers of electrical tape to give the bundle some rigidity. Hopefully it will last!

    Name:  harness 9.jpg
Views: 9332
Size:  34.9 KB

    Name:  harness 10.jpg
Views: 9357
Size:  40.3 KB

    0 Not allowed!
    Last edited by nordwulf; 21 October 2010 at 00:55.

  2. #2

    Join Date
    07 May 2022
    Location
    France
    Posts
    1
    Saab(s)
    9-5 Aero 2004
    Thumbs Up:   0
    Hi,

    Thanks for this particular post, I know I'm digging it but it's really helpful and it motivated me to register myself here ! I'm facing the same issues so I wanted to do the repair myself.

    I wanted to have some information about color and sizes of the wires so I can have the good color for wires and heat shrink sheath.


    From the WIS, I've seen 8 wires that are going to H10-2 connector but in your pictures I can count 9 wires. Which one is the correct number ?

    From the WIS, I've seen the following colors :
    - Pin 1 ->
    - Pin 2 -> Green
    - Pin 3 -> Blue
    - Pin 4 -> Green/White
    - Pin 5 -> Black/White
    - Pin 6 -> Green/Grey
    - Pin 7 ->
    - Pin 8 -> Red/White
    - Pin 9 -> Black
    - Pin 10 -> Green


    So I should order about 50/60 cm of each color to be safe (same for the heat shrink sheath) ?




    Again, sorry for digging this post but it is really helpful !

    Thanks,
    Max

    0 Not allowed!

 

 

Similar Threads

  1. Wire harness on 9-5 Denso Navigation - what kind?
    By nordwulf in forum Tech Talk
    Replies: 3
    Last Post: 30 December 2015, 05:16
  2. Replies: 9
    Last Post: 30 July 2012, 12:57
  3. Windshield replacement / repair
    By nordwulf in forum Tech Talk
    Replies: 13
    Last Post: 31 May 2011, 12:12
  4. Replies: 9
    Last Post: 25 August 2010, 02:01

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
All times are GMT. The time now is 11:06.
Powered by vBulletin® Version 4.2.5
Copyright © 2022 vBulletin Solutions Inc. All rights reserved.