Results 1 to 9 of 9
-
08 December 2011 #1
- Join Date
- 19 Nov 2011
- Location
- Southeast Michigan
- Posts
- 4
- Saab(s)
- 2002 9-5 2.3 Linear
I accidentally put power steering fluid into master cylinder
Guys I need some help!
Last weekend I was changing the rear pads on my 2002 9-5. I turkey basted some of the existing brake fluid to get the level to MIN before starting so as not to overflow during the caliper pressing... finished the job and when i went to re-fill i ACCIDENTALLY topped it off with power steering fluid. (maybe 2-3 ounces worth)
I just realized this today when I was re-checking fluids and my mind flashed back to what I was doing that fateful night.
I have not lost braking power and there are no warning lights on. The level of fluid has not dropped from when I topped it off at MAX.
Pentosin 11S Synthetic Mineral Base Hydraulic Fluid is what I used.. It is what I normally use for the power steering but the bottle looks so similar to the brake fluid I grabbed the wrong one
My question is: Can I baster out the Master cylinder and clean it with some denatured alcohol and repeat, repeat, repeat and fill it back up with DOT 4 brake fluid to solve this?
I am thinking (praying) that at such a low amount that it never reached any of the seals/calipers/etc since the PS fluid should float to the top of brake fluid
(? i think ?)
If not, there goes Christmas as I will be emptying the bank to have the brake system re-done.
Thanks for any advice
-
08 December 2011 #2
Mike Moderator
- Join Date
- 30 Jul 2010
- Location
- Rochester, New York, USA
- Posts
- 1,985
- Saab(s)
- Saab-less
Are you sure the PS fluid is less dense than the brake fluid? If it is, and it managed to get down into the brake lines, you'll have a hard time getting it out; It'll be harder to get out than air bubbles. If you don't think it left the cylinder, then I would just baster it out. I wouldn't probably do anything with the alcohol though. My guess is the biggest problem that could arise if you left the power steering fluid in is that it won't have the same low compress-ability as the brake fluid. The power steering fluid will also have a more consistent viscosity from regular operating temps to lower temps in cold weather, were brake fluid tends to become a tad bit thicker.
My vote is to just strain it off the top (assuming it's less dense), top it off, let it sit a bit, and then strain some more off the top just in case and fill it up. Just what I would do though.Free SaabWorld Stickers
"Sometimes it is better to travel than it is to arrive." - Robert Pirsig
-
08 December 2011 #3
Mike Moderator
- Join Date
- 30 Jul 2010
- Location
- Rochester, New York, USA
- Posts
- 1,985
- Saab(s)
- Saab-less
Oh, and just for reference, the boiling point of DOT 1 brake fluid (the lowest standard) is 401 F, and typical boiling points for power steering fluid is upwards of 425 F.
Also, Pentosin says the top operating temp is 266+FFree SaabWorld Stickers
"Sometimes it is better to travel than it is to arrive." - Robert Pirsig
-
08 December 2011 #4
- Join Date
- 19 Nov 2011
- Location
- Southeast Michigan
- Posts
- 4
- Saab(s)
- 2002 9-5 2.3 Linear
Not sure it's less dense.. I looked in the reservoir and could see no defining "line" indicating that it was floating at the top. I am going to baster it out tonight and retop it with blue DOT4. I will then bleed the system with the power bleeder I am ordering right now..
What a stupid mistake!
-
08 December 2011 #5
Frank Administrator
- Join Date
- 30 Jul 2010
- Location
- USA - Netherlands
- Posts
- 7,901
- Saab(s)
- previous: 2006 9-3, 2001-06 9-5, 2011 9-4X
When was the last time the brake fluid was replaced? It is not that difficult to flush the entire system and have fresh brake fluid in there.
-
08 December 2011 #6
- Join Date
- 19 Nov 2011
- Location
- Southeast Michigan
- Posts
- 4
- Saab(s)
- 2002 9-5 2.3 Linear
It has not been replaced in many years... About 5.
I just ordered a Power Bleeder and some Blue DOT 4 online and am planning on power bleeding the whole system as soon as it arrives.
If I escape this MAJOR FAIL I will be counting my lucky stars. AND labeling all the fluids in my garage!
-
18 December 2011 #7
Roger Cook Saab Enthusiast
- Join Date
- 24 Jan 2011
- Location
- Ypsilanti, MI
- Posts
- 201
- Saab(s)
- 2008 9-5 Aero, 2006 9-3SC 2.0T, 2000 Viggen 'vert, SAAB Quantum, 2000 9-5 retired at 318K miles
-
18 December 2011 #8
- Join Date
- 19 Nov 2011
- Location
- Southeast Michigan
- Posts
- 4
- Saab(s)
- 2002 9-5 2.3 Linear
Yes, I received it and did the bleed. The fluid came out brown at all the bleeders and then turned to bright blue.
No sign that the green pentosin had gone past the master cylinder reservoir. All is well so far.. thanks for all your help!
-
25 February 2018 #9
- Join Date
- 15 Sep 2016
- Location
- Pittsburgh, PA
- Posts
- 27
- Saab(s)
- 2000 9-5 Gary Fisher edition
So the oil near the brake calipers had absorbed some moisture and allowed rust to develop. Thus, the rust color.
This was good fortune in disguise, since it prompted you to flush the rusty, water laden fluid out instead of just topping off the reservoir. 😌
Similar Threads
-
How do you flush a power steering system in the '99 saab 9-3?
By Fox Cain in forum Saab 900 and 9-3 (1994-2003)Replies: 5Last Post: 18 September 2018, 14:43 -
Power steering fluid change
By photousa in forum Saab 9-5 (1998-2009)Replies: 1Last Post: 15 November 2011, 15:40 -
Exhaust Manifold / Cylinder Head Question
By photousa in forum Saab 9-5 (1998-2009)Replies: 2Last Post: 17 October 2011, 23:43 -
(accidentally?) adjustable steering wheel
By classicred900 in forum Saab 900 (1979-1994)Replies: 6Last Post: 06 August 2011, 10:57