Welcome to the world of Saab ! Register
Results 1 to 6 of 6
  1. #1
    Jeffrey
    Master SaabTech/Moderator Burnsside42's Avatar
    Join Date
    25 Oct 2010
    Location
    Point Pleasant, PA
    Posts
    1,316
    Saab(s)
    - 86' 9KT - 95' 9K Custom CS - 06' 9-3 Combi - 07' 9-7X Arc - 08' 9-3 Convertible - 08' 9-3 TurboX -

    Post Saab 9-4X Service Rear Message Displayed on DIC - DTC C0407 - Doc ID 2867044

    While this PI is written for the new 9650 and 9-4x, it can also help diagnose and repair XWD 9-3 9440

    Service Rear Message Displayed on Driver Information Center (DIC), DTC C0407 with Symptom Code 64 or C0403 with Symptom Code 62 Set - (Jun 6, 2012)
    Subject: Service Rear Axle Message Displayed on Driver Information Center (DIC), DTC C0407 with Symptom Code 64 or C0403 Symptom Code 62 Set
    Models: 2010-2012 Buick LaCrosse
    2010-2012 Cadillac SRX 2011 Saab 9-4X
    Equipped With All-Wheel Drive (AWD)



    This PI is being revised to add a Note after step 22 and provide the part number for the eLSD Clutch Piston Kit, which is now available from GM parts. Please discard PI0703.

    Condition/ConcernSome customers may comment that the service rear axle message is displayed on the driver information center (DIC).Note: GDS diagnostics must be used to confirm what DTC is set in the CCM. When checking the vehicle for DTCs, the Rear Differential Clutch Control Module (CCM) may report either C0407 64 or C0403 62 set as current or in history.

    Recommendation/Instructions
    Important: Both the Cadillac SRX and the Buick LaCrosse will also require a calibration update to the clutch control module (CCM). Follow SI and TIS2WEB instructions to reprogram the CCM with the latest calibration available through TIS2WEB. Important: It is very important that after the repairs are completed, the electronic limited slip differential (eLSD) clutch fluid fill and check procedure be followed exactly. Low fluid level can cause the DTC C0403 62 to repeat or induce DTC C0407 64. The unit MUST be filled with 350 ml of eLSD clutch fluid through the vent fitting opening (see Section III in this bulletin).

    DTC C0403 Symptom 62:
    The DTC C0403 symptom 62 may be set due to a concern with the torque transfer device (TTD) internal filter. To obtain a filter kit that will include a filter and gasket, please order parts currently available and listed in the parts section of this communication. Refer to the Differential Clutch Oil Filter Replacement procedure in SI.

    DTC C0407 Symptom 64:
    Important: The single biggest cause of a C0407 symptom 64 is low eLSD clutch fluid. Low eLSD clutch fluid may be caused by improper filling of the eLSD clutch, an internal piston seal leak or a leak at the pump cover gasket. The eLSD clutch MUST be filled with 140 ml (0.15 qts) of eLSD clutch fluid through the vent fitting opening in the TTD clutch cover and NOT the TTD clutch cover plug. For internal piston seal leaks, it is not necessary to replace the complete eLSD clutch assembly or the complete rear differential. The C0407.64 code is set when the fluid is low in the TTD clutch. There are several conditions that can cause the eLSD clutch to be low on fluid:
    External leakages on the eLSD and TTD clutch (see Section I in this bulletin).
    Electronic limited slip eLSD clutch oil leaking into the rear differential through the electronic limited slip eLSD clutch piston seals (see Section II in this bulletin).
    Improper filling of the TTD clutch during the eLSD and TTD clutch filter/gasket service or pump replacement (see Section III in this bulletin).
    Important: Replacing the control module or module kit WILL NOT correct this condition. Removing the control module and valve will purge some of the air from the pump motor cavity, which will give a false condition that a new control module was the correct repair. Section IInspect the vehicle for external leakages. Below is a list of common leaks and suggestions for repair.
    Leak from the TTD clutch oil cover - retighten the bolts or replace the gasket and refill the eLSD clutch.
    Leak from the eLSD clutch pipes - replace the leaking fitting and reattach the pipe using a new clip. Refill TTD clutch.
    Leak from steel balls on the eLSD and TTD clutch - replace the eLSD or TTD clutch assembly.
    Once a leak is corrected, the eLSD clutch oil level should be confirmed with the eLSD clutch Oil Inspection procedure in section III. The eLSD clutch is properly filled when fluid level is level with the bottom of the eLSD clutch cover plug and pump motor current is between 2.5-3.5A. Both conditions MUST be met for the TTD clutch to be considered full. Follow the fill process in Section III if fluid needs to be added.Section IIIf no external leakages are found, follow the instructions below to confirm an internal piston seal leak.
    1. Check for rear differential fluid level being too high (overfilled). Use the Rear Axle Lubricant Level Inspection procedure in SI to check fluid level. The fluid level should be even with the bottom edge of the fill plug opening if not overfilled.
    2. Confirm that either a) or b) exists.
    a) eLSD clutch fluid level is low. Use the eLSD clutch oil inspection procedure in SI to check fluid level. Fluid level should be level with the bottom of the eLSD clutch cover plug when fluid level is not low.
    b) eLSD clutch fluid level is OK, but the current of the eLSD clutch pump motor is consistently below 2.5A (differential clutch fluid level will NOT be OK if the pump motor current is consistently below 2.5A). Observe the current using the scan tool and monitoring the rear eLSD clutch pump motor current parameter. As the pump motor turns on/off, the current will cycle from 0A to 2.5-3.5A, if functioning normally.
    Name:  2549355.jpg
Views: 8905
Size:  19.6 KB

    Name:  2549356.jpg
Views: 9125
Size:  47.7 KB
    3. If the rear differential fluid level is too high and either a or b exists, then the eLSD clutch oil is leaking past the eLSD clutch internal piston seals (6 or 7) into the rear differential. The service fix is to replace the eLSD clutch piston only using the following procedure.
    Electronic Limited Slip Differential Clutch Piston ReplacementCautionIt is very important to observe maximum cleanliness when working on the differential clutch. Dirt particles can seriously damage the function and service life of the differential clutch.
    1. Raise the vehicle. Caution It is very important to observe maximum cleanliness when working on the differential clutch. Dirt particles can seriously damage the function and service life of the differential clutch.
    2. Drain the rear differential fluid.
    3. Remove the rear axle assembly from the vehicle. Refer to the Differential Carrier Assembly Replacement procedure in SI.
    4. Place the rear differential assembly on a clean work bench.
    WarningThe hydraulic pressure in the differential clutch is very high. To prevent personal injury, wait for at least 10 minutes before removing any parts from the differential clutch.
    5. Remove the limited slip differential clutch low and high pressure pipes from the differential clutch.
    6. Remove the electrical connector from the limited slip differential valve and remove the harness from the clip.
    7. Remove the limited slip differential clutch bolts (Qty: 6).
    8. Remove the limited slip differential clutch from the differential carrier assembly.
    Name:  2789536.jpg
Views: 8180
Size:  42.6 KB
    9. Remove the retaining ring that secures the differential clutch pack to the clutch housing.
    Name:  2789542.jpg
Views: 8088
Size:  46.9 KB

    Name:  2789543.jpg
Views: 8054
Size:  32.7 KB
    10. Remove the differential clutch pack from the clutch housing. Hold the housing in one hand and flip over to allow the clutch pack to fall into the other hand.
    Name:  2789545.jpg
Views: 8255
Size:  36.9 KB

    Name:  2806109.jpg
Views: 8007
Size:  42.3 KB
    11. Apply compressed air to the low pressure pipe connector port to release the piston from the differential clutch housing.
    12. Remove the eLSD clutch piston from the housing.
    Name:  2789546.jpg
Views: 8046
Size:  37.6 KB
    Note: If the piston spring is removed, ensure proper orientation when reinstalling. Spring fingers must be positioned as shown above.
    13. Install the new eLSD clutch piston into the housing. Push down to seat.
    14. Reinstall the differential clutch pack into the housing.
    15. Reinstall the retaining ring that secures the differential clutch pack to the clutch housing.
    16. Remove the low and high pressure pipe connectors from the limited slip differential clutch. Discard the connectors and pipe spring clips.
    17. Install the NEW low and high pressure pipe connectors and spring clips to the limited slip differential clutch.
    Tighten Start by hand than tighten the connectors to 7N·m (62 lb in).
    18. Reinstall the limited slip differential clutch to the differential carrier assembly.
    Name:  2806114.jpg
Views: 8077
Size:  46.9 KB
    19. Reinstall the limited slip differential clutch bolts (Qty: 6).
    Tighten Tighten the bolts in proper sequence to 30 N·m (22 lb ft).
    20. Reinstall the limited slip differential clutch low and high pressure pipes to the differential clutch.
    Name:  2806112.jpg
Views: 8262
Size:  38.6 KB
    21. Reinstall the electrical connector to the limited slip differential valve and harness to the clip. Route the electrical harness under the pressure lines as shown.
    Name:  2806115.jpg
Views: 8085
Size:  43.4 KB
    22. Remove the TTD clutch cover fill plug (2) and add 140 ml (0.15 qts) of eLSD clutch fluid. Install the fill plug and tighten to 14 N·m (10 lb ft).
    Note: 140 ml (0.15 qts) if only the piston was replaced and 300 ml (0.32 qts) if the piston and filter were replaced. May be easier to get the required fluid into the unit if the assembly is tilted up on the pinion nose.
    23. Install the rear axle assembly to the vehicle. Refer to the Differential Carrier Assembly Replacement procedure in SI.
    24. Refill the differential rear axle. Refer to the Differential Rear Axle Lubricant Level Inspection in SI.
    25. Lower the vehicle.
    26. Start the vehicle and allow running for 5 minutes at idle.
    27. In Park, cycle the throttle from idle to wide open throttle briefly 5 times waiting a minimum of 30 seconds between each WOT cycle to cycle solenoids to purge air.
    28. With the engine running, observe the scan tool rear limited slip differential clutch pump motor current parameter. The parameter display should be above 2.5A when the pump is on. If the current is below 2.5A, then shut the vehicle off and recheck the level by performing steps 29 through 33.
    29. To stabilize the clutch oil level, let the vehicle rest 10 minutes with the ignition off.
    30. Raise the vehicle and support the vehicle.
    31. Remove the differential clutch cover plug (2) and recheck the differential clutch fluid level.
    32. The eLSD clutch fluid should be level with the bottom of the eLSD clutch cover plug hole (2). If the eLSD clutch is overfilled, drain out fluid until it is at the proper level. Add fluid through the vent opening (1) if the eLSD clutch is low on fluid.
    33. Install the TTD clutch cover plug (2) and re-tighten to 14 N·m (10 lb ft).
    34. Lower the vehicle.
    35. Drive the vehicle 10 km (6 mi) to confirm that the DTC does not reset.
    Section IIIIf improper filling is suspected or a leak is corrected, follow the instructions below to check and properly fill the TTD clutch fluid.The TTD clutch is properly filled when the fluid level is level with the bottom of the TTD clutch cover plug and the pump cavity (4) is full. The pump cavity is full when the pump motor current is between 2.5-3.5A while the engine is running and the pump motor is running. The current cycles from 0 to 2.5-3.5A as the pump turns off/on. Both conditions MUST be met. If the pump motor current is consistently below 2.5A, then the pump motor cavity (4) is low on fluid.

    Important:
    When filling the eLSD clutch housing after repairs, the fluid must be able to flow over the top of the internal wall of the pump cavity (3 and 4), making it imperative that the fluid is filled through the vent opening (1) with the cover plug (2) installed. The bottom of the cover plug opening (2) and the internal wall (3) are at the same level. If the cover plug (2) is not installed, the fluid will fill the eLSD clutch oil sump (5) and run out of that opening (2) before it can flow over the wall (3) into the pump cavity (4).


    If the clutch fluid level is level with the bottom of the eLSD clutch cover plug (Fig. 3, B) and the pump motor current is below 2.5A, then the eLSD clutch pump cavity is empty.If this is the case, the TTD clutch needs to have fluid added using the following procedure:
    1. Clear all DTCs.
    2. Raise the vehicle and support the vehicle.
    Name:  2806115.jpg
Views: 8085
Size:  43.4 KB
    3. Remove the vent hose (1) from the fitting.
    4. Attach the fill hose to the vent fitting and fill the TTD clutch through the vent opening on the cover. Ensure that the fill plug (2) is installed prior to adding fluid through the vent fitting.
    5. Install the vent hose.
    6. Lower the vehicle.
    7. To stabilize the oil level, let the vehicle rest 10 minutes with the ignition off.
    8. Start the engine and allow to run for 5 minutes at idle.
    9. In Park, cycle the throttle from idle to wide open throttle briefly 5 times waiting a minimum of 30 seconds between each WOT cycle to cycle solenoids to purge air.
    10. With the engine running, observe the scan tool rear limited slip differential clutch pump motor current parameter. If the parameter display is above 2.5A when the pump is on, then go to Step 11. If the current is below 2.5A, then shut the engine off and go back to Step 1.
    11. Shut the engine off.
    12. Raise the vehicle and support the vehicle.
    13. Remove the differential clutch cover plug (2) and inspect the differential clutch fluid level.
    14. The differential clutch fluid should be level with the bottom of the eLSD clutch cover plug hole (2). If the eLSD clutch is overfilled, drain out fluid until it is at the proper level. Add fluid through the vent opening (1) if the TTD clutch is low on fluid.
    15. Install the TTD clutch cover plug (2) and re-tighten to 14 N·m (10 lb ft).
    16. Lower the vehicle.
    17. Drive the vehicle 10 km (6 mi) to confirm that the DTC does not reset.

    See Techlink article dated October 2010 for further details regarding the rear eLSD clutch system features and operation.Parts Information
    Part Number Description
    22956728 eLSD Clutch Piston Kit $65 Retail
    20986573 Filter Kit, Differential Clutch Oil $47.67 Retail
    88863349 (In Canada, use 88863350) Differential Clutch Fluid
    88900401 (In Canada, use 89021678) Differential Rear Axle Fluid $27.58 Retail
    88900330 (In Canada, use 992694) Rear Axle Limited Slip Fluid (Additive) $13.00 Retail
    [FONT=Trebuchet MS]
    KW: AWD TTD eLSD dtc PI0703 PI0423 PIP4886 PIP4731 c0407-64 c0403-62 c0407-02 9650 9-4 9-4x transfercase calibration sps update GDS2 low PTO oil
    [/FONT]
    Last edited by Burnsside42; 03 January 2015 at 15:55.
    European Motor Services, LLC - Point Pleasant, PA 18950 - www.europeanmotorsvc.com

  2. #2
    Saab Enthusiast
    Join Date
    13 Oct 2011
    Location
    Romansville (Thorndale), PA , USA
    Posts
    177
    Saab(s)
    2011 9-4x, 2008 9-3 Aero, had 2005 9-3 Arc, '93 9000CSE, '86 9000Turbo
    I had the Service Rear Axle Message on my 9-4x. General Sales fixed it, said it was the piston, and 9hrs of labor. Just over $1300 (USD) for parts and labor.

    EDIT 1/6/2014: I grabbed the invoice out of my glove box.. it says...

    Internal Differential Fault
    Piston failing causing filter to clogg
    Codes C0403 and 0402
    R&R Rear differential and overhauled
    Updated vehicle software to latest programs code 1AA32
    Last edited by Mark_Venture; 06 January 2014 at 17:24.

  3. #3
    Jeffrey
    Master SaabTech/Moderator Burnsside42's Avatar
    Join Date
    25 Oct 2010
    Location
    Point Pleasant, PA
    Posts
    1,316
    Saab(s)
    - 86' 9KT - 95' 9K Custom CS - 06' 9-3 Combi - 07' 9-7X Arc - 08' 9-3 Convertible - 08' 9-3 TurboX -
    You got robbed. Warranty only pays a few hours. $1300 sounds like near DOUBLE what it should have been.
    You could have done that job in less than 10 hours yourself....
    European Motor Services, LLC - Point Pleasant, PA 18950 - www.europeanmotorsvc.com

  4. #4
    Saab Enthusiast
    Join Date
    13 Oct 2011
    Location
    Romansville (Thorndale), PA , USA
    Posts
    177
    Saab(s)
    2011 9-4x, 2008 9-3 Aero, had 2005 9-3 Arc, '93 9000CSE, '86 9000Turbo
    I didn't have much choice. GM/Cadillac dealers in the area wouldn't touch it. I don't know of any other shops I trust. Its the only Saab (former) dealer unless I drive it 45+ minutes one way to the former Saab dealer in Delaware. And I don't have time to do it myself.

  5. #5

    Join Date
    31 Dec 2013
    Location
    minneapolis
    Posts
    1
    Saab(s)
    2011 9-4x
    the service rear axle light came on for my 2011 9-4x at 600 mile mark. The entire Haldex unit had to be replaced - total cost $7,000 and my cost $4,000 since the warranty was not being honored. Not good.

  6. #6
    Saab Fan
    Join Date
    04 Dec 2012
    Location
    Jersey City NJ
    Posts
    38
    Saab(s)
    '11 9-4X Aero, '07 9-3 Aero Conv, had 9-3 Conv (99) 9000 (86)
    Quote Originally Posted by Mark_Venture View Post
    I didn't have much choice. GM/Cadillac dealers in the area wouldn't touch it. I don't know of any other shops I trust. Its the only Saab (former) dealer unless I drive it 45+ minutes one way to the former Saab dealer in Delaware. And I don't have time to do it myself.
    I had same issue, Park Ave Saab Lotus in Maywood NJ fixed it for under $400 I think, they said I have to do it and add fluid to the rear axle every 10k miles.

 

 

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
All times are GMT. The time now is 05:07.
Powered by vBulletin® Version 4.2.5
Copyright © 2024 vBulletin Solutions Inc. All rights reserved.