Results 1 to 10 of 10
-
05 September 2013 #1
- Join Date
- 05 Sep 2013
- Location
- South Carolina
- Posts
- 4
- Saab(s)
- '06 9-5 S/C, '03 9-3 SE-C, '86 SPG
gearbox + CEL off and on
Greetings, all - first time poster here.
My 2003 9-3cv has been throwing the gearbox / check engine lights for about a year now. I have not completely resolved the issue, because I've been able to reset with my techII tool to satisfy the system for months at a time.
Within the past 4-6 weeks, it has been happening with greater frequency - probably 1-2 times per week. Same scenario: gbx+CEL lights come on and limp home mode kicks in. (Normally happens after driving for about 10-15 min, not at cold start, couple times after a hot start.)
TechII always displays the fault as '01 N/A' - guessing that means there is one fault, code not available (??).
I have a new neutral safety switch ready to install, but wanted some input on this before I dig in to be sure that I'm addressing the correct issue.
Thanks,
TT
-
05 September 2013 #2
Jeffrey Master SaabTech/Moderator
- Join Date
- 25 Oct 2010
- Location
- Point Pleasant, PA
- Posts
- 1,317
- Saab(s)
- - 86' 9KT - 95' 9K Custom CS - 06' 9-3 Combi - 07' 9-7X Arc - 08' 9-3 Convertible - 08' 9-3 TurboX -
Sounds like a NSS issue to me - not sure what the message you are getting from the Tech2 is. Have you pulled the DTC from the trans and the engine?
European Motor Services, LLC - Point Pleasant, PA 18950 - www.europeanmotorsvc.com
-
05 September 2013 #3
- Join Date
- 05 Sep 2013
- Location
- South Carolina
- Posts
- 4
- Saab(s)
- '06 9-5 S/C, '03 9-3 SE-C, '86 SPG
sorry...DTC??
-
05 September 2013 #4
Jeffrey Master SaabTech/Moderator
- Join Date
- 25 Oct 2010
- Location
- Point Pleasant, PA
- Posts
- 1,317
- Saab(s)
- - 86' 9KT - 95' 9K Custom CS - 06' 9-3 Combi - 07' 9-7X Arc - 08' 9-3 Convertible - 08' 9-3 TurboX -
Diagnostic Trouble Code - the fault code.
European Motor Services, LLC - Point Pleasant, PA 18950 - www.europeanmotorsvc.com
-
05 September 2013 #5
- Join Date
- 05 Sep 2013
- Location
- South Carolina
- Posts
- 4
- Saab(s)
- '06 9-5 S/C, '03 9-3 SE-C, '86 SPG
ok, thank you. Is that different from the code I get on my Tech2? I am getting "N/A" on my tech2 for that fault whenever the gearbox light comes on. Wondering if a leaky vac line might be the culprit.
thanks,
TT
-
14 May 2014 #6
- Join Date
- 13 May 2014
- Location
- Greenville SC
- Posts
- 6
- Saab(s)
- 2003 9-3
Hey good to know you have a tech 2' and hopefully by now you have figured out the solution to the problems you described. I'm having similar problems with my 2003 9-3. I'm in Greenville
-
14 May 2014 #7
- Join Date
- 05 Sep 2013
- Location
- South Carolina
- Posts
- 4
- Saab(s)
- '06 9-5 S/C, '03 9-3 SE-C, '86 SPG
-
15 May 2014 #8
- Join Date
- 13 May 2014
- Location
- Greenville SC
- Posts
- 6
- Saab(s)
- 2003 9-3
Very interesting, however I doubt that my 9-3 problem will be as simple as that. I am curious about the club that you mentioned in the local area, but that is it geared toward socialization or problem solving ? Perhaps you could send me a link?
-
15 May 2014 #9
- Join Date
- 13 May 2014
- Location
- mass
- Posts
- 1
- Saab(s)
- 2000 9-3 2.0 turbo
im trying to post my saab for a part out but cant figure it out...its a 2000 saab 9-3 2.0 turbo...any one need anything or can help me post it up..
-
26 September 2016 #10
- Join Date
- 07 Sep 2016
- Location
- Pa
- Posts
- 1
- Saab(s)
- 2003
I am having a neutral mode when i put it in drive or if it goes in gear it only stays there for a few feet then goes back, the gearbox light and stabilization malfunction light also comes on . The DCT is P1743 any thoughts??? Please Help I am stranded.